Alexor PC9155D-433 Przewodnik Instalacji Pobierz pdf (Strona 69)

5.3 Programming Descriptions

5-45

[804][330] WT4911 Maximum Bell Activation Time

This value determines the maximum time the wireless bell/siren will sound before automatically turning off.

[804][900] General Wireless Options

[851] GPRS/Ethernet Module Programming

Refer to the associated manual for programming details.

[898] Wireless Device Enrolment

See Chapter 2 for details.

[899] Template Programming

See Chapter 4 for details.

[900] Alarm System Version

When this section is entered the version of the panel is displayed as a 4-digit decimal entry.

E.g., The entry 1234 = Version 12.34. This is a read-only value.

[904] Wireless Module Placement Test

See Chapter 2 for details.

[905] Wireless Keypad Placement Test

See Chapter 2 for details.

[906] Wireless Siren Placement Test

See Chapter 2 for details.

[990] Installer Lockout Enable

This feature is designed to prevent installers other than the original from resetting the panel. If enabled, the panel gives a distinctive audible indication on power up

(the phone line relay will click 10 times). If a hardware default is attempted while lockout is enabled, the default does not occur and the false default attempt is

logged to the event buffer. This feature has no effect on a software default (all programming returns to the factory defaults).

[991] Installer Lockout Disable

This section disables the Installer Lockout feature described above.

[996] Restore Wireless Default Programming

All programming in section [804] Wireless Device Programming returns to the factory defaults.

[998] Restore Panel Default Programming

All programming in the PC9155 returns to the factory defaults, except for the Wireless Device Programming sections.

[2]

ON: Pre-Alarm Signal Enabled. When the system begins entry delay the entry delay time is sent to the wireless siren. If the wireless siren does not

receive a disarm command during the entry delay time, the siren will go into alarm.

OFF: Pre-Alarm Signal Disabled. When the system begins entry delay no entry delay time is sent to the wireless siren. The siren will not go into

alarm until it receives a signal from the panel to tell it to go into alarm.

[3]

ON: Strobe Squawks Enabled. This feature provides a visual indication on outdoor sirens when the system has been successfully armed or disarmed

without sounding the siren.

• One flash indicates that the system has been armed.

• Two flashes indicate the system has been disarmed with no alarms in memory.

• Three flash pairs indicates the system has been disarmed with alarms in memory.

OFF: Strobe Squawks Disabled. Outdoor siren LEDs will not flash (strobe) during arming or disarming.

This option functions independently of the programming in section [014] Opt. 1.

[4]-[8]

For Future Use

When these options are enabled or disabled, they affect all wireless devices on the system.

Option Description

[1]

For Future Use

[2]-[6]

For Future Use

[7]

ON: RF Jam Disabled. RF Jam conditions will NOT be detected, displayed and communicated.

OFF: RF Jam Enabled. RF Jam conditions will be detected, displayed and communicated.

[8]

ON: Global Placement Test. Module selection is NOT required for the placement test. Entering section [904]-[906] begins the testing. All zones,

keypads, and sirens that are enrolled are tested. Individual devices do not have to be selected.

OFF: Individual Module Placement Test. On entering section [904]-[906] a 2-digit entry is required to select the zone, keypad or siren to be tested.

1 2 ... 64 65 66 67 68 69 70 71 72 73 74 ... 87 88

Komentarze do niniejszej Instrukcji

Brak uwag

Alexor PC9155D-433 Przewodnik Instalacji Strona 69

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Alexor PC9155D-433